Inhouse Exhibition: Save The Date 18+19 Sept 2024 Find Out More >>

Morso EH Mitre Guillotine - Hydraulic

Part Number
The MORSO-EH is a fully automatic electric/hydraulic mitring machine, with a noise level below 70db - the perfect machine to cut picture mouldings in production - wooden, plastic, and MDF mouldings. In principle MORS?-EH does the same work as the MORS?-F , but with the MORS?-EH you have your work done automatically by pushing two push buttons. The MORS?-EH is safe to operate as you must activate both push buttons at the same time to have the machine work, and therefore you cannot get your fingers underneath the knives. With the MORS?-EH you can do production work all day long. The MORS?-EH can be delivered either single phase or three phase with voltage to your requirements.

If you compare the MORS?-EH to a double mitre saw, you will find that first of all the cut with a saw is not as clean and accurate as with the MORS?-EH. Secondly there will very often be a problem with the dust from the saw. On MORS?-EH there is no dust, as the waste of the moulding is lead straight to the ground, which means it is not necessary to buy an expensive dust extractor. Another thing is the waste of the moulding. By using a mitre saw, there will always be about one centimetre of waste per cut, but if you see the MORS?-EH the waste is minimized to about 1 mm per cut. A difference of one centimetre may not sound of much, but if the number of cuts are 200 per day, the unnecessary waste of moulding is 200 cm per day, which is about 520 meters per year..... ( Working 5 days a week... ). If you compare the time spent per cut, the MORS?-EH normally uses 1 to 1,5 second to finish the moulding. With the saw, it is about the same, if not a little more, so even here we cannot find an advantage with the double mitre saw....

The MORS?-EH is supplied with the same standard equipment as the MORS?-F plus it has:

Extension table to the left side.
Automatic Rebate Supports and Moulding Clamps.
Measuring scale 1500 mm with two adjustable stops - you can cut the short and long lengths of a frame without having to re-adjust the measurements.
Automatic cutting cycles for both large and small mouldings - which means that the machine always does the trim cut which is very important.
Adjustable length of stroke (3 positions) - when using the lowest cutting position the cutting cycle of two cuts only takes between 1 and 1.5 seconds.
Technical data for MORS?-EH

Double mitre 45 degrees

Single mitre up to 90 degrees

Cutting width max. 100 mm (4 ")

Cutting height max. 180 mm (7 ")

Square cutting 70/70 mm (2 3/4")

Measuring scale up to 1500mm (59 ")

Net weight 135 kilos (298 lbs)

Motor, single phase 1.1 kW

Motor, three phase 1.1 kW

Pumping capacity 7 l/min.

Working pressure 80 bar

Power transmission 660 kilos

Tank contents 6 l.

Optional extra'

Also available with Turbo making the unit upto 50% quicker.

Packed dimensions 70 x 60 x 115, 135kg

Order before 3 pm and we'll aim to despatch stock items under 30kg the same day, on a next day service Monday to Friday.

Please allow 1 to 2 working days for delivery if you are in Highlands, Islands or Northern Ireland.

These parcels are sent are sent by APC Courier as standard.

For urgent orders, please phone us as we can offer recommend using one of our Premium delivery services or even same day couriers [at extra cost]

Sadly there is no one size that fits all so we offer a personal service tailored to your needs - We have lots of options and specialists so we can offer:

Next Day nationwide delivery with APC Couriers at low cost or we offer FREE Eco Delivery upto 30kg locally

Pallet service for some machines which is very economical but only suitable for certain items [and goods that are simple to tranship]

Dedicated vehicles with either curtain side [and tail lift unloading in some cases]

Specialist machinery movers with HIab crane off loading and position machines in your workshop or factory. Some of these options take a few days to organise and have availability.. If you are in a rush for a machine, give us a call during normal office hours so we can see what is possible for your chosen machine and location.

We also export our tools and machinery to over all of Europe and to 145 other countries worldwide! Depending on your needs we can offer:

TNT or DHL Courier – Fastest upto 30kg and Online orders.

International Airfreight – Fast for larger items and machines needed in a hurry

Containerisation for several machines, tools and spare parts if you need a complete workshop – Most economical

LCL Shipments for individual machines – Very Economical for one of heavy machines

Have you own Transport or Courier Company?

Use our click and Collect System and we can do the documentation for DHL, TNT, Fedex or others

Lead Time: 46 Days
- +
- OR -
  • N/A
More Information
Part Number MOEH
Manufacturer Morso
Write Your Own Review
You're reviewing:Morso EH Mitre Guillotine - Hydraulic

Product Information Leaflet