Wadkin Spare Parts
(88 Products)
Spares for Wadkin Machines: We have an enormous range of Wadkin Spare Parts in stock for recent and old Bursgreen, Leicester or Durham machines. Using our extensive industry experience and knowledge of Wadkin Spares parts we can help you keep your woodworking machinery running. If you can not find the spare part for your Wadkin machine - send us an enquiry, we can find it or repair or possibly manufacture a replacement for you.
-
-
-
-
Clutch Plate / disc for rise and fall on thicknesser bed on Wadkin BT500 Thicknesser Wadkin BTS500 Planer Thicknesser Wadkin BT630 Thicknesser Wadkin BTS630 Planer ThicknesserLead Time: 6 Days€94.73€113.68 -
3 mm square Diamond grinding wheel for Wadkin Profile Grinder D = 230 d = 31.75 mm [1 1/4"]Lead Time: 21 Days€227.84€273.41 -
5 mm square Diamond grinding wheel for Wadkin Profile Grinder D = 230 d = 31.75 mm [1 1/4"]In Stock€263.82€316.58 -
Diamond Grinding Wheel for Wadkin NQ straight knife planer blade grinder Diamond Grinding Wheel for sharpening and grinding TCT planer blades D = 150 H = 70 d = 22.2Lead Time: 6 Days€232.64€279.17 -
Wadkin T630 Variable Speed Drive Belt 22 x 8 x 1180mmLead Time: 6 Days€233.84€280.61 -
Set of 50ml permabond adhesive complete with initiator for fixing bandsaw tyres (recommended one set per wheel) Instructions: The rim of the Bandsaw Wheel being treated should be cleaned thoroughly removing all traces of old rubber and adhesive right down to the bright metal surface. Do not use oil based cleaning materials, such as paraffin as this will be detrimental to the use of the new adhesive applied. For the strongest adhesive to metal, Primer should be used. This must be stirred thoroughly prior to the application of a medium brush coat to prepared metal surfaces. Allow the primer to dry for at least one hour before applying the adhesive. Prepare the rubber tyre by wiping thoroughly with a clean rag and lightly roughen the inside with emery paper. Apply an even film of the mixed adhesive to both surfaces by brush, roller or serrated trowel. Allow these to dry for 10-20 minutes or until they can be touched by the knuckles Without any adhesive being transferred. Joining the Surfaces. As the tyre has to be stretched onto the rim of the wheel, care must be taken to ensure that the tyre lies central on the wheel rim. As the adhesive is a contact' type, it is advisable to place spacers between the tyre and the wheel at 3"- 4" intervals until the centralisation mentioned above has been achieved. The spacers can then be removed allowing the adhesive surfaces to come together. As much pressure as possible should be applied to the tyre to ensure a good bonding - paying special attention to the edges. The wheels should be allowed to stand for 1-2 hours before use. Finally, true up the rubber and put a slight crown on the face. This is done by revolving the wheel, preferably on the machine, and holding against it a wooden block covered with emery cloth. Check the wheel for balance before use. An alternative method to the above is to apply the adhesive to one surface only and bond immediately. This will give a much lower initial bond strength than the previous method. Maximum bond strength using this method will take approximately 5-7 days to develop. F'. U 1In Stock€58.76€70.51 -
The iTECH Safety 315 Saw Guard is a replacement table saw guard that sets the benchmark for riving knife mounted safety on saw benches and panel saws with blades up to 315mm. This guard rises and falls with the sawblade height adjustment so as to reduce blade exposure, this combined with gravity side covers improves the protection for the operator. The transparent casing enables the operator to see the blade clearly. The integrated dust port and more enclosed design imporives and enhances extraction from the saw to make your workshop environment cleaner and safer. The kit includes Guard and 2.8mm Riving Knife and is suitable for blades up to 315mm diameter. Outlet size 42mm * If for use on SEGA300 please contact us in advance as slightly different riving knife will be supplied.In Stock -
High quality die cast aluminium pump suitable for moulders where a controlled amount of lubricant is required. Suitable for most moulders such as Leadermac, Wadkin or Weinig Manual Hand Pump -Model H-600-6 specifications : - Reservoir Capacity : 0.6 Litres Pressure : 15 Kg/cm2 Discharge : 6cc/stroke Material of Reservoir : Aluminium CastingLead Time: 6 Days€ Enquire -
-
Nx111ÿÿ 4.7mm 30 Deg Right Stylus For Wadkin Profile grinderLead Time: 6 Days€50.36€60.43 -
Nx112ÿÿ 4.7mm 30 Deg Left Stylus For Wadkin ProfiLead Time: 6 Days€50.36€60.43 -
-
NX133 3mm Radius and square stylus for Wadkin NX grinderLead Time: 6 Days€50.36€60.43 -
Nx40 4.7mm Rad & Square Stylus For Wadkin Profile Stylus for Wadin Profile Grinder different shapes suitable for Wadkin Profile Grinders NX, NV etcLead Time: 6 Days€50.36€60.43 -
-
Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€ Enquire -
Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€ Enquire -
Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€ Enquire -
Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€ Enquire -
Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€ Enquire -
-
Pressure Track Pad for use on Wadkin Double ended tenoner . This rubber block with 2 fixing holes is used as a top pressure on Wadkin WN WO WE DP DA etc Price dependant on quantities ordered. Minimum Order quantities apply. Please contact us for more informationLead Time: 105 Days€11.99€14.39 -
Vacuum support pod for Weeke and Homag CNC Router Size of pad : 120mm x 50mm Height of pad : 100mmLead Time: 105 Days€155.89€187.07 -
-
-
-
